�� KG-X is an intelligent steering assist gyro optimized for RWD drift.

60229 KG-X Steering Assist Gyro

��spec��
�� High Speed Response (NORMAL / HCS)
�� AGS function
�� End point independent right setting function
�� PCA function
�� Number of input channels: 2 CH (steering signal: 1 ch)
* When using gain adjustment remotely. please use the 4ch transmitter.
�� Power supply: 4.8 V to 7.4 V
�� Size: 20.0 �� 24.0 �� 14.0 mm
Weight ��: 8.3 g
�� High rigidity aluminum outer case
��Compatible models��
�� KR - 415FHD / KR - 413FH / KR - 241FH / KR - 211FH / each company receiver
�� RSx series / BSx series / servo from each company
��Recommended categories��
1/10 electric drift car (RWD / AWD). 1/10 electric F-1. 1/10 electric touring

If you increase the gyro gain with RWD drift car etc..
AGS function to suppress hunting where the steering servo violently vibrates left and right.
Left and right independent end point setting function to optimize left and right counter amount.
Such as the PCA function which can arbitrarily set the blending ratio between gyro control and driver operation.
It is a next-generation drift gyro that covers the functions required for the current drift scene.

�� AGS suppresses hunting!
AGS is the meaning of Anti Glitch System. In the conventional steering gyroscope.
If you increase the gyro gain with 2WD drift car etc.. steering servo violently vibrates left and right Hunting (= glitch) occurs.
If it is used as it is it causes the servo to generate heat. which in the worst case was causing the servo to be damaged.
KG-X has an AGS function that suppresses hunting by its own algorithm.
By adjusting the AGS volume. even if you set a high gain that was unusable by hunting.
It became possible to operate the servo normally.

�� Set endpoints independently on the left and right!
In KG - X. it is possible to individually set the maximum turning angle of the counter steer during drift on the left and right.
We solve the two big problems with the conventional steering gyro as shown below.
(1) With a steering gyro without an end point setting. a break angle occurs more than the limit point when operating the gyro
There was a problem that the linkage and the knuckle were damaged.
Since KG - X regulates the break angle beyond the end point set in the initial setting even if the gyro action and the steering operation are combined.
It prevents excessive operation.
(2) In the steering gyroscope which sets the common end point on the left and right.
Due to the installation of the chassis and the convenience of the linkage there was inconvenience such as right turning angle is enough or left turning angle is not enough.
KG-X memorizes left and right independent end points with simple initial setting. so gyro operation amount easily matches on the left and right.
Once the initial setting is done. the setting contents are retained until the next setting change. so there is no stress of readjustment.

�� Feeling steering feeling as desired with PCA!
PCA stands for priority control adjuster (Priority Control Adjuster)
This function changes the blend ratio of the signal from the gyro that is mixed inside the KG-X and the signal of the steering operation.
If the gain of the steering gyroscope is set high to increase the turning angle of the counter steer.
In the conventional gyroscope. gyros assertiveness became stronger and the control performance was trade-off.
Even if you set a large gain by properly adjusting the PCA.
You can keep control performance that you can not feel gyroscopic intervention.

�� Remote control of gain with 3 ch input!
Gain is the amount of movement of the countersteer when the steering gyroscope is activated.
Since the KG - X has a 3 - channel input port. connect this channel to the 3 ch (or 4 ch) of the receiver.
By operating 3ch of the transmitter it is possible to change the gain even during running.
* Optional black connection cable (100 mm) No. 36519 is required for remote control.

�� New high speed communication system HCS compliant!
HCS system which compresses the communication processing time of receiver and servo to 1/4 and makes the operation feeling of the servo more direct.
KG-X also supports HCS system.
* When using with HCS. please use in combination with HCS compatible receiver (KR - 415FHD etc.) and HCS compatible servo (BSx3 / RSx3 etc.).
* When changing the response mode. please make initial setting of KG-X


��set content��
KG-X main unit x 1
Black connecting cable (for 1 ch-IN connection) x 1